Nitrous-express DIESEL STACKER NITROUS NXD12003 User Manual download pdf

NXD12001, 12002, 12003

DIESEL STACKER NITROUS INSTALLATION INSTRUCTIONS

Congratulations on the purchase of your Nitrous Express Diesel Nitrous System. This system does not

add fuel and is intended to be used with an engine management system that can add nitrous enrichment fuel

through the engines injectors Nitrous Express utilizes only the highest quality components designed for the

use of liquid nitrous oxide. To properly utilize these specially designed components and obtain the trouble-

free operation that this system is capable of producing, it is extremely important that you read all

instructions carefully. Pay special attention to the important notes at the end of the installation steps and the

tuning tips listed at the back of this instruction sheet.

To insure proper system assembly and operation, carefully read the following installation procedures

thoroughly before beginning. Use NX thread sealer on all pipe thread connections, DO NOT use any sealer on

flare connections, hose, or bottle connections. Use no other sealing compounds or Teflon tape. All threads

must be clean and dry, apply only enough sealer to wet the threads, too little is better than too much.

Excessive tightening of parts is not necessary, snug is enough. If it is necessary to remove a fitting installed

with the red NX sealer heat must be applied to release the sealing agent. NOTE: Due to shipping restrictions

all NX nitrous bottles arrive empty. Before beginning the installation the N2O bottle should be filled by a

NX accredited filling station.

Before starting any installation procedures care- fully disconnect the vehicle negative battery cable. If

there is any question about this operation, consult the vehicle owner’s manual!

MOUNTING THE BOTTLE

Slide bottle into bottle brackets. Use illustration (A) as a guide for proper alignment. Locate bottle

assembly in a mounting area that will provide easy access to bottle valve, for hose connection and bottle

removal. Using the bottle unit as a pattern, mark and drill four 3/8” holes. Note: Before drilling holes be

sure to check beneath the area being drilled for obstructions, fuel lines or fuel tank. Then secure unit to

mounting surface. (Recommend minimum of four 5/16” grade five bolts). Align bottle in brackets so that

the valve outlet is pointing down- ward to the mounting surface (See Illustration A) and tighten the bottle

bracket bolts. NOTE: This is VERY IMPORTANT so that the internal siphon tube will pick up liquid

nitrous.

ILLUSTRATION A

1 2 3 4 5 6 7

Summary of Contents

Page 1

NXD12001, 12002, 12003 DIESEL STACKER NITROUS INSTALLATION INSTRUCTIONS Congratulations on the purchase of your Nitrous Express Diesel Nitrou

Page 2 - ELECTRICAL HOOK-UP

SOLENOID MOUNTING 1. The NX Dry nitrous systems are supplied with the world’s most sophisticated N2O solenoid. Pay special attention to the “inlet-ou

Page 3 - WIRING SCHEMATIC

A. The WOT Switch must be mounted inside the vehicle using the accelerator pedal to activate the nitrous system. B. Assemble the micro-switch

Page 4 - POWER TUNING TIPS:

SAFETY TIPS 1. Never permit oil, grease, or any other readily combustible substances to come into contact with nitrous cylinders, valves, solenoids

Page 5

3. In stock engine applications and street usage the spark plugs should be at least 2 steps colder than stock. Do not use platinum tip, extended tip o

Page 6

18. If you run an NX system of 150+ horsepower you must use a high octane racing type fuel. These are some tips to help you choose and maintain the co

Page 7

Comments to this Manuals

No comments

Nitrous-express DIESEL STACKER NITROUS NXD12003 User Manual

Browse online or download User Manual for For the car Nitrous-express DIESEL STACKER NITROUS NXD12003. Nitrous Express DIESEL STACKER NITROUS NXD12003 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Nitrous-express DIESEL STACKER NITROUS NXD12003